Black Widow: Difference between revisions

From Danno's Rocket Wiki
No edit summary
Tag: Reverted
No edit summary
Tag: Manual revert
Line 14: Line 14:
Black Widow is a rocket I built in late 2015 / early 2016 to replace [[Home Alone]] after [[2015 Launch Reports#Home Alone, L990|its crash in Elsberry]]. The kit is a Rocketry Warehouse (now Composite Warehouse) Dominator 3, no longer in production. It's very similar in size to Home Alone, but with a different fin shape featuring a curved trailing edge. The kit came with a very nice looking red-anodized nose cone tip and tailcone motor retainer, so I finished it in a black and red color scheme.
Black Widow is a rocket I built in late 2015 / early 2016 to replace [[Home Alone]] after [[2015 Launch Reports#Home Alone, L990|its crash in Elsberry]]. The kit is a Rocketry Warehouse (now Composite Warehouse) Dominator 3, no longer in production. It's very similar in size to Home Alone, but with a different fin shape featuring a curved trailing edge. The kit came with a very nice looking red-anodized nose cone tip and tailcone motor retainer, so I finished it in a black and red color scheme.


<gallery mode="packed">
<gallery mode="slideshow">
File:NARAM58-looking-up.png|View from onboard camera.|alt=Frame from onboard camera looking down at two men, while the rocket is on the launch pad.
File:NARAM58-looking-up.png|View from onboard camera.|alt=Frame from onboard camera looking down at two men, while the rocket is on the launch pad.
File:NARAM58-blue-streak.jpg|First liftoff.|alt=Frame from pad camera showing a black rocket lifting off with a bright blue flame.
File:NARAM58-blue-streak.jpg|First liftoff.|alt=Frame from pad camera showing a black rocket lifting off with a bright blue flame.

Revision as of 21:39, 1 October 2023

Black Widow is a rocket I built in late 2015 / early 2016 to replace Home Alone after its crash in Elsberry. The kit is a Rocketry Warehouse (now Composite Warehouse) Dominator 3, no longer in production. It's very similar in size to Home Alone, but with a different fin shape featuring a curved trailing edge. The kit came with a very nice looking red-anodized nose cone tip and tailcone motor retainer, so I finished it in a black and red color scheme.

  • Frame from onboard camera looking down at two men, while the rocket is on the launch pad.

    View from onboard camera.

  • Frame from pad camera showing a black rocket lifting off with a bright blue flame.

    First liftoff.

  • The lower airframe of a black rocket, covered in dust and lying in a dusty field. A silver Volkswagen GTI is in the far distance.

    Landed in the Argonia dust.

Launches

NARAM 58 (2016), J449

NARAM 58 (2016), K530

Airfest 22 (2016), L1040

Midwest Power 14 (2016), K830

SLRA Fall 2016, K650

Checklist

(This checklist will change somewhat due to the redesign project.)

Pre-launch (before leaving town):

  • Clean everything!
  • Charge batteries: TeleGPS, TeleBT, BRB transmitter, all cameras, Mobius, ham transceiver, drill
  • Clear memory in cameras
  • Check TeleGPS config and reset / clear memory
  • Check Mobius config (correct video mode; sync clock), test and clear memory
  • Test TeleGPS/TeleBT and leave transmitter battery unplugged
  • Install new Duracell battery for Raven; check Raven config (set main pyro altitude to 900 feet); switch OFF and remove battery
  • Check contents of recovery pack

Pre-launch (night before launch):

  • Assemble motor - remove delay charge
  • Install motor in rocket
  • Assemble ejection charges (1.5g Goex + wadding) x4
  • Refold / repack parachute and rubberband

Chute is folded in quarter lengthwise, then gores folded in in quarters and laid on top, then chute folded / rolled across. Bundle should end up approx. 13.5" long with gores on the inside and should be thin enough to easily slide into tube.

At the field:

  • Install Raven battery; verify that green "safe" lamp is lit, and zip-tie battery to sled
  • Switch Raven on to test; verify that red "armed" lamp is lit while Raven is on and 8-9 voltage beeps are heard. Switch Raven off.
  • Check terminal blocks for voltage
  • Secure (4) ejection charges in charge wells with electrical tape and connect leads to terminal blocks

Pay special attention to orientation of the sled in the coupler when assembling. The arming switch must be aligned with the designated access hole, and the "up" end of the sled must be aligned with the "up" end of the coupler.

  • Insert sled into coupler, attach forward bulkhead plug and assemble coupler with lock washers and hex nuts
  • Attach aft shock cord / nomex between booster & coupler
  • Pack drogue & attach to aft shock cord
  • Check / adjust friction fitting between booster & coupler
  • Attach forward shock cord / nomex to coupler
  • Thread forward shock cord through forward section and attach forward section to coupler with rivets
  • Bundle forward shock cord w/masking tape
  • Attach main parachute to forward shock cord
  • Switch TeleGPS and TeleBT on, check for comm & GPS lock, switch TeleBT off (leave TeleGPS on!)
  • Assemble nose cone with lock washer and eye nut
  • Attach forward shock cord to nose cone
  • Fit nose cone to payload section, install shear pins
  • Verify that TeleGPS is still transmitting
  • To pad with rocket, pad camera & recovery pack

At the pad:

  • Place pad camera
  • Switch on-board camera on, REMOVE LENS CAP & start recording
  • Rocket on rail
  • Switch Raven on
  • CHECK FOR PROPER NUMBER OF CHARGE CONTINUITY BEEPS [HI-HI-HI-HI]
  • Apo-Main-Backup Apo-Backup Main...High=connected, low=disconnected
  • Igniter in motor
  • Igniter leads
  • Start pad camera
  • Return to LCO
  • Switch TeleBT on and verify that TeleGPS still has GPS lock and is transmitting - if not, ask LCO to hold launch
  • Go For Launch
Retrieved from "http://rocketwiki.danno.org/index.php?title=Black_Widow&oldid=1052"