Black Widow (altimeter bay redesign): Difference between revisions

Revision as of 16:08, 10 September 2023

Black Widow has not flown since November 2016. It’s a good rocket but has some usability and recovery problems. The goal of this project is to refit it with new electronics and solve as many known problems as possible, making this back into a workhorse high-performance rocket. I have five flights’ worth of data and video to review and see where improvements can be made. This page is just a copy of my own project notes.

Update 4/23/2023: I found out that the battery I was planning to use (2S, 1200mAH, 30C) was not going to be suitable, because in a short circuit it could produce more current than the BlueRaven's pyro outputs could handle (36A vs. 22A). I found another battery (1S, 380mAH, 25C) that should be suitable, maxing out at 9.5A. I should have the batteries tomorrow and the proper wiring connectors on Tuesday, and will need to alter the sled design and reprint it.

Update 4/30/2023: Successful bench test of new altimeter and wiring:

Update 9/9/2023: Yeah, I've let this sit for a while. I have a countdown app on my phone that helpfully tells me that there are 48 days left until Midwest Power, plus I might have an opportunity to do a shakedown flight at my local launch the weekend before. So I need to get going!

Update 9/10/2023: I settled on the Fruity Chutes 48" Iris as a main parachute, and ground tested with it. This is Buster's pilot chute, and is also going to be used as the main for the Kerbal 5, which is about the same weight. I have a new 80" Top Flight Recovery streamer to use as a drogue.

TODOs as of 9/9/2023:

Assemble & test-fit new nose sled
Test old Mobius camera and make sure it still works
Clean everything
Buff / polish (how-to)
Paint alignment keys where needed
Design and print new "ground station" bits (see below)

Project notes:

Entirely new 3D-printed sled
- New BlueRaven altimeter
- 3.7V 380mAH LiPo battery
  - Extend the battery's plug to a locking JST connector that can be accessed from the removable end of the coupler, so the pin can be put in the pin switch before connecting the battery
- Pull-pin switch instead of magnetic switch
- Wiring should be hidden or managed by the sled as much as possible [for now I think I'm just keeping wiring neat with zip ties]
TeleGPS
- Design and print a new sled
Camera
- Is it possible to remove the old shroud and replace it with a new one for the new camera? [In short, no; if we need to switch to the new camera, we'd have to replace the entire upper airframe tube.]
- Otherwise, is it possible to add the new camera horizontally in the center bay? [No.]
Recovery
- New drogue streamer
  - Re-watch old videos and see if there’s a solution to drogue problems (spinning, falling nose-down)
  - Have multiple notes about the Spheracutes drogue pulling the upper and lower airframes together after apogee, and either colliding or nearly colliding
- Use 48" Iris Ultra as main parachute
  - Have had multiple occurrences of the primary charge not getting the main out
Physical assembly
- Make sure everything has clear alignment keys (stripes on outside)
- Check coupler fitting on cold & hot days
- Check fit & usability of plastic rivets
Telemetry
- Determine whether I can run the BlueRaven and Altus Metrum apps together
- Add a phone holder to the Yagi antenna
- Add “feet” to the ends of two reflectors on one side of the Yagi so it can be set down on the ground or on a tabletop (with the reflectors vertical and the camera and phone right way up)
Sim & test fit DMS L1000 (currently sims about 10k/750mph)
Update the checklist

@@ Line 12: / Line 12: @@
 Update 9/9/2023: Yeah, I've let this sit for a while. I have a countdown app on my phone that helpfully tells me that there are 48 days left until Midwest Power, plus I might have an opportunity to do a shakedown flight at my local launch the weekend before. So I need to get going!
+Update 9/10/2023: I settled on the [https://shop.fruitychutes.com/collections/iris-ultra-standard-chutes/products/iris-ultra-48-standard-parachute-12-5lbs-20fps Fruity Chutes 48" Iris] as a main parachute, and ground tested with it. This is [[Buster|Buster's]] pilot chute, and is also going to be used as the main for the [[Kerbal 5]], which is about the same weight. I have a new [http://topflightrecoveryllc.homestead.com/page2.html 80" Top Flight Recovery streamer] to use as a drogue.
+<center>
+{{#evu:https://www.youtube.com/watch?v=OgTwI5djTeM
+|alignment=inline
+}}
+</center>
 TODOs as of 9/9/2023:
 * Assemble & test-fit new nose sled
-* Select new parachutes [currently thinking Fruity Chutes 48" Iris as main, Top Flight 80" streamer as drogue]
-* Check rivet holes and re-drill if needed
-* Ground test
 * Test old Mobius camera and make sure it still works
 * Clean everything
@@ Line 25: / Line 31: @@
 Project notes:
-* Entirely new 3D-printed sled [designed, first iteration printed]
+* Entirely new 3D-printed sled
 ** New [https://www.featherweightaltimeters.com/blue-raven-altimeter.html BlueRaven] altimeter
 ** [https://www.amazon.com/dp/B08DD5MTKM?psc=1&ref=ppx_yo2ov_dt_b_product_details 3.7V 380mAH LiPo battery]
@@ Line 33: / Line 39: @@
 * TeleGPS
 ** Design and print a new sled
-** Could it use a pull-pin switch also?
 * Camera
 ** Is it possible to remove the old shroud and replace it with a new one for the new camera? [In short, no; if we need to switch to the new camera, we'd have to replace the entire upper airframe tube.]
 ** Otherwise, is it possible to add the new camera horizontally in the center bay? [No.]
 * Recovery
-** Possibly replace drogue chute
+** New drogue streamer
 *** Re-watch old videos and see if there’s a solution to drogue problems (spinning, falling nose-down)
 *** Have multiple notes about the [https://spherachutes.com/products/apex-drogue Spheracutes drogue] pulling the upper and lower airframes together after apogee, and either colliding or nearly colliding
-** Possibly replace main chute
+** Use 48" Iris Ultra as main parachute
 *** Have had multiple occurrences of the primary charge not getting the main out
-*** Maybe a deployment bag?
 * Physical assembly
 ** Make sure everything has clear alignment keys (stripes on outside)